Audi A4/S4/A5/S5 B8 Vag Com Kodları | Sistem Destek Uzmanı
Sistem Destek Uzmanı

Audi A4/S4/A5/S5 B8 Vag Com Kodları



Kodlama işlemleri riskli işlemlerdir. İşlemi yapmadan önce mutlaka kodların yedeğini alınız.

MMI 3G Gizli Menü Aktivasyonu

[5F – Information Electr.]
[Adaptation – 10] -> Channel 6
0 değerini 1 yapın

Menüye erişmek için car ve setup tuşlarına birlikte 5 saniye basılı tutun.

________________________________________
MMI 2G Gizli Menü Aktivasyonu

[07 – Control Head]
[Adaptation – 10] -> Channel 8 -> Change 0 to 1

Menüye erişmek için car ve setup tuşlarına birlikte 5 saniye basılı tutun.
________________________________________

Bluetooth mikrofon hassaslık ayarı

Gizli menü
Diagnose
Settings
Mic sensiblity – choose -6db/0db/+6db

________________________________________

Kamera Resim Ayarı

[6C-Back-up Cam.] [Security Access – 16] (enter security code 22351)

[Adaptation – 10]

Channel 10 (Brightness)

Default: 50 (Set between 1-100)

Channel 11 (Contrast)

Default: 50 (Set between 1-100)

Channel 12 (Saturation)

Default: 50 (Set between 1-100)

Channel 13 (Temperature)

Default: 50 (Set between 1-100)

________________________________________

MMI 3G Başlangıç Ekranı Değiştirme

Enable through the “hidden menu”:
– navigate to ‘car/carcodingvehicle’
– choose the model of choice in ‘configuration line’
– select ‘Update Splashscreen’
– restart MMI

________________________________________

Disable After-wipe of windscreen wipers

[09 – Cent. Elect.] [Coding – 07] -> [Dropdown] -> “x ** 8K1 955 119 ** WWS xxxx” -> Long Coding Helper -> Byte 1
Bit 3 – Remove check mark (1 = active)
________________________________________

Disable amber corner lights 

[09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 10
Submodule 0
Bit 3 – Set to 0 to disable amber side markers (U.S. vehicles)
________________________________________

Disable Key warning (keyless models)

[46 – Central Conv.] [Coding – 07] -> Long Coding Helper -> Byte 9
Bit 7 set to 0 (Uncheck)
________________________________________

Disable LED ‘wink’ on turn signal – pre facelift

[09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 3
Bit 2 – LEDs remain at full brightness with parking lights (1 = active)
Bit 7 – Turn off LED-strip DRLs with indicators (1 = active)

________________________________________

Disable LED ‘wink’ on turn signal – facelift

09 – Cent. Elect.] [Security Access – 16] (enter security code. One of the default codes is- 20113)
[Adaptation – 10] -> Channel 3 (Heading Wink Brightness)
Default Value is 26, Setting value to 88 (Makes it identical to normal brightness)
________________________________________

Dim LED wink on turn signal for US cars

Instead of complete wink off, there is another mod that comes as stock in Europe. There is an LED dim instead of wink.

Starting with factory setting:

Central Electronics 09

Coding 07

Long Code helper

Byte 02 – Check bit 6 (Side Marker as DRL)

If you have already eliminated the winking, the you will need to go to Byte 03 and undo the modification. In other words, the winking DRL options (Bit 7) will need to remain checked/on as it was in the factory setting.

________________________________________

Disable bulb error message with LED reverse lights installed

https://www.a5oc.com/forums/a5-perfor…tml#post296914

________________________________________

Disable “Lights are on” Warning

[09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 5
Bit 3 – Set to 0 to disable “lights are on” warning when you open the door.
________________________________________

Disable NAV & Phone warning messages while entering data at speed

[5F – Information Electr.] -> Adaptation -> Set channel 2 & 3 to 250
________________________________________

Emniyet Kemeri Uyarısı Kaldırma

[17 – Instruments] [Coding – 07] -> Long Coding Helper -> Byte 0
Bit 2-4 – Seat Belt Warning

________________________________________

To mute the Soundaktuator

A9 Structure Borne Sound
Adaptation 10
At Channel drop down choose “Volume of structure borne noise actuator” (only choice)
Enter a value in the proper box (0% = mute )
________________________________________

Enable Adaptive brake lights 

[46 – Comfort System] [Coding – 07] -> Long Coding Helper -> Byte 8
Bit 0 – Emergency Brake Flashing via Turn Lights active (1 = active)
Bit 1 – Emergency Brake Flashing via Brake Lights active (1 = active)

________________________________________

Enable Optical rear parking for cars without front parking sensors

[10 – Park/Steer Assist] [16 – Security Access – 71679] do it [07 – Coding] Byte 0 – Bit 4 change 0 to 1
________________________________________

Enable Automatic Gear selection shown in DIS 

[02 – Auto Trans] [Adaptation – 10]
Select “Single Gear Display” from top channel drop down menu
Select “D on/S on” from New value drop down menu
________________________________________

Enable Automatic Hill Hold Assist ‘lite’*only works on certain abs modules – see below link*

[03 – ABS brakes][Security Access – 16] (Enter code presented by program)
[Coding – 07] -> Long Coding Helper -> Byte 1
Bit 6 set to 1 to enable hill hold assist.

http://www.audienthusiasts.com/VagComABS.html
________________________________________

Enable Auxiliary ventilation

[5F – Information Electr.] [Coding – 07] -> Long Coding Helper -> Byte 6
Bit 1 – Set to 1
[Hidden menu] [car] [cardevicelist] [Auxiliary heating] Enable
[08 – Auto HVAC] [Coding – 07] -> Long Coding Helper -> Byte 1
Bit 3 – Set to 1
Bit 4 – Set to 1
________________________________________

Enable Battery meter *does not appear to work on facelift cars with MMI 3G+ HDD Navigation*

For MMI equipped cars

[Hidden menu] [car] [cardevextdevicelist] [Battery] Enable
[Hidden menu] [car] [carmenuoperation] [Battery] Set to 5
Reset MMI
or
[56 – Radio] -> Adaption -> Channel 39, add 16 to your value

For symphony, Chorus and Concert

Select module 56 – Radio

Select “Adaptation – 10

Select channel 39

Add 16 to the present value
“test”

“save”

“Done, Go Back” and “Close Controller
________________________________________

Enable DIS with Efficiency Program for MY2010+ (Not a complete Program without the Start/Stop System)

[17 – Instruments] [Adaptation – 10] -> Channel 77
change 0 to 255
________________________________________

Enable Double Disarm Beep

[46 – Central Conv.] [Adaptation – 10] -> Channel 63
Add 4
ensure Module 46, Byte 1, Bit 2 is ticked. This activates the alarm audible notification option
________________________________________

Enable Drivers Memory Seat

36: Seat Mem – 07 Coding – Long Coding Helper – change Byte 2, bit 0, to 1

Seat memory will be there however greyed out in MMI

Press and hold down unlock button on key fob for 5 seconds for the windows to come down

Press and hold down lock button on key fob for 5 seconds for the windows to go back up

In MMI, Seat Adjustment you are now able to find Driver’s seat, you can set Key memory on/off. Set it “on” for both keys separately.
________________________________________

Enable DRL Selectable via MMI

[09 – Cent. Elect.] -> [Coding – 07] -> Long Coding Helper -> Byte 3
Bit 5 set to 1
________________________________________

Enable DRL

[09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 2
Bit 1 = DRL via Front Side markers
Bit 2 = DRL via High Beams
Bit 3 = DRL via Fogs
Bit 4 = DRL via LEDs
Bit 5 = DRL via Parking Lights
Bit 6 = DRL via Side markers
Bit 7 = DRL via Tail lights
________________________________________

Enable Audi Drive Select without the buttons

By far the best guide is here – http://www.audienthusiasts.com/Project_ADS.html
________________________________________

Enable Euro parking lights that turn on signal at night

[09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 9
Bit 0 – Set to 1
________________________________________

Enable interior lighting option for pre-facelift

MMI Basic (Symphony/Concert radio) – (NON-MMI – 2G/3G):
Code:
[56 – Radio]
[Coding – 07] -> Long Coding Helper -> Byte 8 Bit 7 – Interior Light Settings active – (1 = active)

MMI high (2G):
Code: Enable the Interior lighting (extended) MMI item:
[07 – Control Head]
[Adaptation – 10] -> Channel 1 add 2 to the existing value

MMI high (2G hidden menu as alternative)
If you choose to use the 2G hidden menu you will find the setting using the following:
DIAG SETTINGS -> APK 0x01, 0x0B, 0x0C -> Interior lighting (extended)

MMI 3G and MMI3G+

This can only be activated through hidden menu

Enter hidden menu – choose car – choose carmenuoperation – select interior light – set to 5 to allow adjustment whist moving – press return – select cardevicelist – choose interior light and press to fill box in – press return

*at this point 3G owners do step below, 3G+ go to (3G+ only) below

(3G only) Reset MMI (press setup, scroll wheel and top right button next to scroll wheel at the same time)

(3G only) Option will show in MMI

(3G only) [09 – Cent. Elect.]

[Coding – 07] – Long Coding Helper -Byte 16 Bit 6 – Set this bit manually to 1

(3G+ only)

Facelift needs an extra setting to activate the option.
Hidden Menu > car > carbusassignment > Interior Light > change from 9 to 1.

Reset MMI

Enable interior lighting for facelift cars

[09 – Cent. Elect.]
[Coding – 07] -> [Long Coding Helper] -> Byte 16
Bit 6 – Interior/Ambience Lighting Adaptation active
Hidden Menu > car > carbusassignment > Interior Light > change from 9 to 1
________________________________________

Enable fog lamp to come on for the same side as that turn signal

[09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 4
Bit 0 – Check the box or change :Bit 0 set to 1
________________________________________

Enable Front Turn Signals as Parking lights

[09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 10
Bit 0- Check the box or change :Bit 0 to 1
Once the change has been made you can enable the front turn signals as DRL’s by making the following change:
[09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 2
Bit 6 – Check the box or change :Bit 0 set to 1
________________________________________

Enable Gauge Test/Needle Sweep 

[17 – Instruments] [Coding – 07] -> Long Coding Helper -> Byte 1
Bit 0 – Check the box for “Gauge Test/Needle Sweep active”
________________________________________

Enable Headlights on all the time

[09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 4
Bit 5 – Check the box or change (Bit 5 Set to 1)
________________________________________

Enable Horn confirmation on locking

[46 – Cent. Convenience.] [Coding – 07] -> Long Coding Helper -> Byte 1
Bit 2 – Check the box or change (Bit 2 Set to 1)

________________________________________

Enable Import CDs to MMI’s HD

[Hidden menu]
Main/Diagnose/Settings
Import Media
Set to 4 of 4 “Copy/Ripping”
________________________________________

Enable Independent Fogs control with high beams

[09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 4
Bit 1 – (Front) Uncheck the box or change :Bit 1 to 0
Bit 2 – (Rear) Uncheck the box or change :Bit 2 to 0
________________________________________

Enable Lap Timer 

[17 – Instruments] [Coding – 07] -> Long Coding Helper -> Byte 1
Bit 3 – Check the box for “Lap Timer active”
______________________________________

Enable Remote Operation Windows and Sunroof 

[46 – Cent. Conv.] [Coding – 07] -> [Long Coding Helper] Byte 2
Bit 2 – Set to 1
______________________________________

Enable Rear Tail Lights on with DRLs

[09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 2
Bit 7 – DRL’s via Tail Lets Active (1 = Active)
________________________________________

Enable Release Parking Brake without putting foot on Brake

[53 – Parking Brake][Security Access – 16] (Enter code presented by program)
[Adaptation – 10] -> Channel 4 Set to 0
________________________________________

Enable Release Parking Brake without putting seatbelt

[53 – Parking Brake][Security Access – 16] (Enter code presented by program)
[Adaptation – 10] -> Channel 7 Set to 0
________________________________________

Enable Reverse mirror tilt

[52 Door Elect, Pass.] -> [Coding – 07] -> [Long Coding Helper] -> Byte 4
Bit 3 and Bit 2 set to 1
________________________________________

Enable Speed on chorus, concert or symphony display

Module 56 – Radio
Adaptation – 10
Channel 2 –> change 0 into 1 (driving school mode active).
New menu item: Under Radio Setup “ON/OFF” driving school mode.
________________________________________

Enable ‘Tourist’ Mode – Headlight Convertor (MMI 2G)

[09-Central Elect]
[Coding – 07]
[Long Coding Helper] – Byte 4, Bit 6 = 1
Enables the ‘connection’ between Cent. Elect and the Headlight Convertor MMI menu item
[55-Xenon Range]
[Adaptation – 10]
[Channel 10] – 0 = Disable 1 = Enable
Press ‘Test’ and then ‘Save’
Enables the Headlight Convertor MMI item under the CAR button.
Restart MMI to see changes.

________________________________________

Enable TPMS
* only works with certain ABS modules – see below link *

http://www.audienthusiasts.com/VagComABS.html
________________________________________

Enable Video in motion on MMI

[5F – Information Electr.] [Advanced ID – 1A] Note 1st Serial number
[Security Access] Enter Digits 6, 13, 10, 14, 11 of the 1st Serial number
[Adaptation – 10] -> Channel 48
Set to 255
Reset MMI
________________________________________

Set Audi parking system – Switch OFF Speed

[10 – Park/Steer Assist] [Adaptation – 10] -> Channel 23
Set to 20 (max value in km/h)
________________________________________

Set ADS to specific preset Comfort, Auto, Dynamic or Individual

[09 – Cent. Elect.][Security Access – 16]
[Adaptation – 10] -> Channel 63
Set to 01 – Comfort, 02 – Auto, 03 – Dynamic or 04 – Individual
[Adaptation – 10] -> Channel 64
Set to 01 – Comfort, 02 – Auto, 03 – Dynamic or 04 – Individual
[Adaptation – 10] -> Channel 65
Set to 01 – Comfort, 02 – Auto, 03 – Dynamic or 04 – Individual
[Adaptation – 10] -> Channel 66
Set to 01 – Comfort, 02 – Auto, 03 – Dynamic or 04 – Individual
*Note all four channels needs to be set to the same value.

________________________________________

Set Headlight washer – Duration

[09 – Cent. Elect.]
[Security Access – 16] [Adaptation – 10] -> Channel 6
change to e.g. 500
________________________________________

Set Headlight washer – Cycles

[09 – Cent. Elect.]
[Security Access – 16] [Adaptation – 10] -> Channel 26
change to e.g. 10
________________________________________

Adjust Consumption in DIS 

[17 – Instruments]
[Adaptation – 10] -> Channel 3
change 100 to xxx (see samples below)

Sample 1 – Calculation based on volume per distance (e.g. l/100km):
DIS: 9,3 l/100 km.
Real: 9,8 l/100 km. (100 * 9,8 / 9,3 = 105,38)
Channel 3 will be changed from 100 to 105

Sample 2 – Calculation based on distance per volume (e.g. MPG):
DIS: 23 MPG.
Real: 24 MPG. (100 * 23 / 24 = 95,83)
Channel 3 will be changed from 100 to 96
________________________________________

Adjust LED brightness

[09 – Cent. Elect.] [Security Access – 16] (enter security code. One of the default codes is- 20113)
[Adaptation – 10] -> Channel 03
Set between 5 and 100 (5 being lowest and 100 brightest)
________________________________________

Select language in DIS:

17 – Instruments
Byte 8 -> Bit 0-4 – ->
Select the language.
________________________________________

Activate SDS for cabriolet:

5F–Information Electr.
Change Byte 15 – Bit 0 to 1
Change Byte 16 – Bit 0 to 0
________________________________________

Change fuel-tank charisterics:

17 – Instruments
Adaption – change channels 30 and 33
________________________________________

To increase radio play time after car is turned off:

In the Hidden Menu:

MMI 2G:
“MMI->SETTINGS->Standby Timer” – will allow you to hear e.g. Radio or CD longer before MMI shutdown (if ignition is OFF) – default 10 min. and the max. is 60 min.

MMI 3G:
From the main screen select ‘onofftimer’, set ‘Standby delay’. The maximum value is 30 minutes

________________________________________

Select language in DIS

17 – Instruments
Byte 8 -> Bit 0-4 – ->
Select the language.

________________________________________

Activate SDS for cabriolet

5F–Information Electr.
Change Byte 15 – Bit 0 to 1
Change Byte 16 – Bit 0 to 0

________________________________________

Change fuel-tank charisterics

17 – Instruments
Adaption – change channels 30 and 33

________________________________________

Audi Drive Select – MMI 2G

09 Central Elec – Long Coding Helper

Byte 7, Bit 5 Change 0 to 1 (tells car ADS is installed, Charisma fault generated)

Byte 8, Bit 2 Change 0 to 1 (Enables engine setting in MMI)

Byte 8, Bit 3 Change 0 to 1 (Enables suspension setting in MMI [I didn’t do this as my suspension isn’t adjustable])

Byte 8, Bit 4 Change 0 to 1 (Enables steering [servotronic] setting in MMI)

Byte 8, Bit 5 Change 0 to 1 (Enables sports diff setting in MMI [I didn’t do this as I don’t have the sport diff])

Byte 17, Bit 7 Change 0 to 1 (Enables MMI display)

—————————————————————-

09 Central Electronic

16 Security Access

Type in code in pop up (for me it was 20113)

Click “Do It!”

—————————————————————-

09 Central Electronic

10 Adaptation

Channels 63, 64, 65, 66

Change Value to 4 for each channel (1 = Comfort, 2 = Auto (default), 3 = Dynamic, 4 = Individual)

Click Test and then Save for each channel

Ensure setting of 4 for all channels again

—————————————————————-

In MMI hidden menu go to Diag settings, Car menus maske, check ‘Charisma’ box and go down to Accept changes (this was already ticked on mine and my mates car). Whilst still in the hidden menu go to Diag settings, APK 0x01, 0x0B, 0x0C, check ‘Charisma’ box and go down to Accept changes.

________________________________________

 

Tags: , , , ,

Bir cevap yazın

E-posta hesabınız yayımlanmayacak. Gerekli alanlar * ile işaretlenmişlerdir





W3Schools